Reportbuilder and TeeChart Pro.

rbuser

After I upgraded I can not open my project - Delphi chrashes - a error
message is shown for about 1/5 of a second...

Using printscreen I found that the error is:
"Error readin form"
"Cannot load package 'Tee710.' It contains unit 'TeeAbout,'which is also
contained in pacakge 'tee100'. Ignore the error and continue? NOTE: Ignoring
the error may cause components to be deleted or property values to be lost."

Is there any easy way to upgrade reporbuilder when using TeeChart pro?
We use TeeChart Pro 7.07.

According to the "Enhancements" log this should be ok:
Version 10.03 - 5/11/2006
-------------------------

RCL
- support for TeeChart 7.07 (Delphi 2006, Delphi 2005, Delphi 7)

But what extra actions have to be done after installing Reporbuilder 10.03
Build 2?

Best regards,

Arvid Haugen

nicocizik

Hi Arvid,

You are receiving this error because Delphi is still loading the version of
TeeChart that is included with the product. Be sure you have fully
installed TeeChart 7.07 before installing ReportBuilder. First, try
reinstalling TeeChart 7.07, then RB 10.03. If this still gives you the same
error, try conducting a corrupt install clean-up as described in the article
below.

--------------------------------------------
Article: Cleaning up a Corrupt Installation
--------------------------------------------

If you have been advised by Digital Metaphors technical support that you may
have a corrupt installation, or if you are having difficulty installing,
compiling or running applications after a ReportBuilder install, then it may
be necessary to manually remove all ReportBuilder files from your system.
Corrupt installations usually result when you are installing over a previous
version of ReportBuilder which was not installed into the default directory,
which was recompiled from the source, or when ReportBuilder files were
manually moved from the default install location. Cleaning up a corrupt
installation, consists of locating all ReportBuilder related files, and
deleting them from your system. The first step is to use the uninstall
program to remove as much of ReportBuilder as possible.


Run the uninstall program

1. Exit Delphi, and all other applications. You should have no applications
running except the uninstall, otherwise you may lose some of your work.

2. Select Start | Settings | Control Panel from your Windows desktop.

3. Double-click the Add/Remove programs icon.

4. Locate the version of ReportBuilder you wish uninstall and double-click
it.

5. The first page of the Uninstall Wizard allows you to choose between an
Automatic or Custom uninstall. Choose Custom and click the Next button.

6. Click the Select All button, then the Next button. Repeat these steps
until you reach the last page of the wizard.

7. Click the Finish button. All of the items you selected will be removed
from the system.

8. After all the ReportBuilder files are removed, you may be prompted to
reboot the system. If this is the case, reboot the system.


Delete the ReportBuilder root directory (and all subdirectories)

1. Using the Windows Explorer, locate the ReportBuilder root directory. The
default directory is:

C:\Program Files\Borland\DelphiX\RBuilder

2. Once you have located this directory, inspect it. If you have any custom
work in this directory which you would like to keep, move it to another
directory.

3. Delete the ReportBuilder root directory.


Delete all remaining ReportBuilder files

1. Using the Windows Explorer, search the entire hard drive for all
occurrences of:

dclRB*.bpl
dclRB*.dcp
rb*.bpl
rb*.dcp

2. Delete any occurrences which correspond to the version you are removing.
All packages are named with the convention NN, where the first number
is the ReportBuilder version and the second number is the Delphi version.
Thus, a typical package name for Delphi 5 would be rbRCL45.bpl. The same
package for Delphi 4 would be: rbRCL44.bpl. Check Installing ReportBuilder
for a list of the packages associated with each version.

3. Using the Windows Explorer, search your hard drive for all occurrences
of:

pp*.*
da*.*
ra*.*

4. These are the prefixes used by individual ReportBuilder units. 'pp' is
used for ReportBuilder units, 'da' is used for DADE units, and 'ra' is used
for RAP units. Depending on which ReportBuilder you have (Standard,
Professional or Enterprise) you may not have all of these unit types.



Additional Notes

1. Never have Delphi running when installing ReportBuilder.

2. All ReportBuilder related files should be stored in the root directory
$(DELPHI)\RBuilder.

3. All ReportBuilder run-time packages should be stored in the
Windows\System directory.

4. You should never have ReportBuilder files in Delphi\Lib, Delphi\Bin or
Delphi\Projects\Bpl.

--
Regards,

Nico Cizik
Digital Metaphors
http://www.digital-metaphors.com